You may wish to compare the specifications to the results, so I placed the table near the chart. The first column identifies the fan. The second says what kind of bearing it has. The third column tells the current draw in amps. SP means Static Pressure, which is stated in mm H2O.

The only other problem to consider is that occasionally, components immediately adjacent to the motherboard fan header can get in the way of the larger 4-pin fan connector, physically preventing connection. This problem also occurs if you try to use an in-line fan speed controller such as the one made by Gelid. The Deepcool GF120 was a fine runner-up. Notice how much quieter the two winners were than their neighbors. They also pushed a lot more air through the restrictive rad than fans of similar unobstructed output. What made the Deepcool fan a runner-up and not one of the winners was the fact that it was a lot noisier than they were. The Deepcool UF120 has been around since 2009. It is still for sale. This fan’s claim to fame is its rubber coating which attenuates vibrations. Further, it comes with four silicon vibration isolators. I have used most vibration isolators, and these are the best kind. Other accessories include a PWM-style 12-volt power tap (a so-called Molex adapter) and wires that shunt 12 volts and 5 volts together to get you a 7 volt Molex adapter. Both the GF120 and the UF120 were supplied by Deepcool. SPL testing on a rad might be misleading because fans -- even when mounted on a rad -- can use the CFM box as a sounding board. I have thought about building a testing chamber out of something large and stiff, but I would have no place to put it . . . and there would still be no assurance that fans did not use it to make a sounding board. Think guitar or violin to get a notion. Originally the house label for Newegg, Rosewill does offer their products for sale in other places these days. They produce a bewildering variety of fans. Not so bewildering are the Hyperborea fans, in 12 cm and 14 cm sizes. These have relatively low speeds as if the makers were aiming at their being used for case fans, as well as on heatsinks and rads. The two units here were obtained retail. Rosewill Hyperborea 12cm San AcePWM fans can be used with PWM splitters, where they all get their power directly from the PSU while tghey get speed control from the motherboard. The first picture shows you an NF-F12. This fan has relatively high static pressure compared to its nominal output. It should. It was invented to be a radiator fan. But then it entered a new life. It became an industrial fan, the NF-F12 industrialPPC. Noctua tells us: First the fans were placed in a test stand, where their free air RPM was observed. Then the fans’ noise was assessed. The standard proxy for what you can hear is the Sound Pressure Level (SPL), measured in decibels and given a type A weighting (dBA). A silent room is about 30 dBA. On the other hand, Cooler Master has brought out the Jet Flo fans, in 120 mm and 140 mm. They have a POM bearing, where a combination of oil and plastic lubricate this fan. Given that the POM, which is like Teflon, forms the mainstay of this bearing, it seems safe to use this on your rads. Jet Flo fans come with red, white, blue, or no LEDs. The six examples here were provided by Cooler Master.

Conceived for industrial heavy duty applications that require enhanced cooling performance and advanced ingress protection, Noctua’s industrialPPC (Protected Performance Cooling) line comprises ruggedized high-speed versions of the company’s award-winning retail models. There were two clear winners here, the Nidec Gentle Typhoon PWM and the Medium speed San Ace “Silent” PWM fans. It is too bad that these fans are among the hardest to get. Noctua is a partnership between Rascom, an Austrian company, and Kolink International, a Taiwanese corporation. Noctua products are legendary, with heatsinks for enthusiasts and industry, and fans with diameters of 40 mm up through 140 mm, also for enthusiasts and industry. In this review, we are looking at a number of fans, two with Low Noise Adapters, which bring our total number of fan sets to 26. Remembering all of these caveats you should be able to make an intelligent decision on which PWM fans to get. Thanks for reading our case fan roundup. Let us know your favorite PWM fans in the comments below. The GlideStream PWM fan was supplied indirectly by Scythe when they provided the Ninja 4 for testing. The Glidestream has a 3-way switch, but the switch was left in H when the GlideStream was tested.

The Blade Master family of fans by Cooler Master have been around for some years. They have a wavy blade, and they’re pretty quiet. The two specimens in our testing were obtained at retail. Too bad they’re sleeve bearing fans. I won’t trust sleeve bearing fans on a heatsink. Noctua’s industrialPPC line also uses a 3-phase motor. Most motors you see have four poles inside. These have six. FDB = Fluid Dynamic Bearing, a patented evolution of the sleeve bearing which causes the lubricating fluid to be recirculated within the bearing. All the outputs all turned out to be underestimates, to one degree or another. The SPL varied. In some instances the fan made fewer dBA than specified. My, how time flies! Enermax released PWM fans with their three-position switches three years ago. We reviewed their fans then. I hauled two of those fans out of their case to compare them with other PWM fans. Although each of these fans has three speeds, we only test them with their switches in the H position, otherwise, I’d never get done.